3D printer
AnkerMake M5
From £948.48 on Amazon UK and Eryone UK as of 6 Oct 2026.
- cheapest today
- £948.48
- listing in stock
- 1
- materials it prints as it comes
- 3/11
Buy the AnkerMake M5
Good for PLA, PETG and TPU.
"Usual" is what it has cost over the last 90 days, from our own price checks.
What it costs to run
About 3p an hour in electricity and 13p in wear: £40.00 a year, before filament.
From its typical power draw (100 W) and expected lifespan (8,000 hours). Change the rate to your tariff's. Cost a print
Not in a hurry?
We'll email you when the AnkerMake M5 drops to your price.
Sign in to set a price alertCompare it with
Side by side- Creality Ender 3 V3 SEGood for PLA, PETG and TPUfrom £149.00Compare
- Creality CR-6 SEGood for PLA, PETG and TPU
- Creality Ender 5 S1Good for PLA, PETG and TPU
AnkerMake M5
| Property | AnkerMake M5 |
|---|---|
| Price | £948.48 |
| Good for | PLA, PETG and TPU |
| Prints as it comes | 3 of 11 materials |
| Enclosure | Open frame |
| Build volume | 235 × 235 × 250 mm |
| Multi-colour | Single colour |
| Stock nozzle | Brass |
| Hotend up to | 260°C |
| Bed up to | 100°C |
| Extruder | Direct drive |
| PLA | Prints out of the box |
| PLA Glow | Needs a hardened nozzle |
| PLA-CF | Needs a hardened nozzle |
| PETG | Prints out of the box |
| PETG-CF | Needs a hardened nozzle |
| ABS | Needs an enclosure |
| ABS-CF | Needs an enclosure |
| ASA | Needs an enclosure |
| Nylon | Needs an enclosure |
| TPU | Prints out of the box |
| PC | Needs an enclosure |
| Filament guide | What the AnkerMake M5 prints |
Specs are each maker's published figures, checked before they're shown; a dash means we haven't checked it yet.
AnkerMake M5 listings
Each listing, on its own and as a combo, checked against its usual 90-day price.
Price checked 6 Oct, 11:15 (UK time) and may change.We earn a small commission if you buy. Your price stays the same.
About the AnkerMake M5
Its specs come from its verified spec sheet, and what it prints from our material table: the same answers as its filament guide and the printer comparisons.
Prices are checked against our own price history, so a deal only counts when the price is genuinely lower than usual, not just lower than a list price.
Common questions
How much is the AnkerMake M5?
As of 6 Oct 2026, the AnkerMake M5 is £948.48 on Amazon UK and Eryone UK. That's about its usual 90-day price, from our own price checks.
Can the AnkerMake M5 print in more than one colour?
No: it prints one colour at a time, with no multi-colour unit.
What filament can the AnkerMake M5 print?
As it comes, our material table says it prints PLA, PETG and TPU. For ABS, ABS-CF, ASA, Nylon and PC, it needs an enclosure added. For PLA Glow, PLA-CF and PETG-CF, it needs a hardened nozzle.
How big is the AnkerMake M5's build volume?
235 × 235 × 250 mm, about 13.8 litres.
Is the AnkerMake M5 enclosed?
No: it's an open frame, so for ABS, ABS-CF, ASA, Nylon and PC it needs an enclosure added.
How SpoolDeal checks prices
The same rules on every page, so a deal badge means the same thing everywhere.
Re-checked through the day
Every tracked listing on Amazon UK and Eryone UK is re-checked through the day, and the most-watched ones every two hours.
Measured against our own history
A deal only counts when the price is below what that reel has actually sold for over the last 90 days, not a seller's “was” price.
An email when it drops
Set a target price on any reel with a free account and we email you when it gets there.
More on the AnkerMake M5
Compare the AnkerMake M5
Waiting for a better price?
Open any reel and set the price you want to pay. We check it through the day and email you when it gets there. Free, and you can switch it off any time.